Product Ref ATR page 2

Audio Technica.: 1800 Series Camera-mount UHF Wireless Systems- :.


With UHF reception (996 frequencies user-selectable in 25 kHz steps), Audio-Technica’s new 1800 Series camera-mount wireless microphone systems provide extremely flexible, professional, and easy-to-use portable wireless solutions. The 1800 Series is available in dual-channel and single-channel systems.

For simultaneous operation of two microphones, dual-channel 1800 wireless systems include the ATW-R1820 dual receiver with two completely independent receiver channels in a single unit. Dual balanced outputs enable signals to be mixed, or independently assigned to each output. Independent audio level controls provide flexible audio mixing and monitoring possibilities.

For those using a single microphone, the single-channel 1800 Series systems include the ATW-R1810 single-channel receiver.

1800 Series wireless systems come equipped with a choice of plug-on and body-pack transmitters. The ATW-T1801 UniPak® body-pack transmitters feature a professional locking 4-pin connector compatible with all Audio-Technica Wireless Essentials® microphones. The ATW-T1802 plug-on transmitters feature a locking XLR connector for adapting dynamic and condenser microphones. Both transmitters offer selectable high and low transmission modes to conserve battery life/maximize power.

Additional 1800 Series features include automatic frequency scanning, Tone Lock™ squelch, back-lit LCD, soft-touch buttons, headphone monitor output with independent level control, and durable metal construction.

Two completely independent receiver channels in a single unit, for simultaneous operation of two microphones (dual-channel systems)

Compact receiver is easy to mount on a camera

UHF reception with 996 frequencies selectable in 25 kHz steps

Automatic frequency scanning for easy selection of open channels

Tone Lock™ squelch system eliminates interference when transmitter is off

Two independent balanced outputs (dual-channel systems)

Headphone monitor output with independent level control

Battery fuel-level indicators on transmitters and receiver

Soft-touch controls for easy frequency selection

True Diversity operation for resistance to multi-path interference and dropouts

LCD frequency and battery status display with backlight, Antenna and AF Peak LED indicators

Dual-channel receiver can operate in single-receiver mode to extend battery life when only one audio channel is in use (dual-channel systems)

Transmitters operate in low or high transmission modes to conserve battery life/maximize power

Easy, user-friendly operation, Clear, natural sound quality, Powered by AA batteries

System components of the 1800 Series and 3000 Series Wireless Systems can be used interchangeably**


OVERALL SYSTEM SPECIFICATIONS

Number of Channels 996 total per band (25 kHz increments), Frequency Stability ±0.005%, Phase Lock Loop frequency control, Modulation Mode FM, Operating Range 100 m (300') typical, Operating Temperature Range 23° F (- 5° C) to 113° F (45° C), Frequency Response 70 Hz to 15 kHz

RECEIVER SPECIFICATIONS

Receiving System Dual independent RF sections, automatic-switching diversity, Image Rejection >50 dB typical, Signal-to-noise Ratio 104 dB at 30 kHz deviation (A-weighted), maximum modulation 37 kHz, Total Harmonic Distortion <1% (±10 kHz deviation at 1 kHz), Sensitivity 25 dBµV, (S/N 60 dB at 5 kHz deviation, A-weighted), Audio Output Balanced: 27 mV (at 1 kHz, ±5 kHz deviation), Output Connector 3-pin mini XLR (TA3M-type), Monitor Headphone Output (typical) 35 mW max., 32 ohm load (per channel), Monitor Headphone Jack 3.5 mm TRS, signals on both Tip and Ring, External Power Requirements 12V DC nominal, 500 mA, Batteries ATW-R1820: Six 1.5V AA alkaline (not included); ATW-R1810: Four 1.5V AA alkaline (not included)
Current Consumption Dual-channel Operation: 600 mA typical; Single-channel Operation 350 mA typical, Battery Life Dual-channel Operation (ATW-R1820): 6 hours typical* , Single-channel Operation (ATW-R1810): 10 hours typical*
* depending on battery type and use pattern

Dimensions ATW-R1820: 85.0 mm (3.35") W x 133.0 mm (5.24") H x 36.0 mm (1.42") D
ATW-R1810: 75.0 mm (2.95") W x 125.0 mm (4.92") H x 32.0 mm (1.25") D

Net Weight ATW-R1820: 425 grams (15.0 oz) (without batteries)
ATW-R1810: 300 grams (10.5 oz) (without batteries)

Accessories Included ATW-R1820: Two flexible UHF antennas; two 18" TA3F to XLRM output cables; belt pouch
ATW-R1810: Two flexible UHF antennas; 18" TA3F to XLRM output cable; belt pouch

BODY-PACK TRANSMITTER SPECIFICATIONS

RF Power Output High: 30 mW; Low: 10 mW, nominal, Spurious Emissions Under federal regulations, Dynamic Range >105 dB, A-weighted, Input Connections High impedance, low impedance, bias, Batteries Two 1.5V AA alkaline (not included), Current Consumption High: 180 mA; Low: 160 mA, typical, Battery Life Approximately 6 hours (High); 8 hours (Low),
depending on battery type and use pattern

Dimensions 66.0 mm (2.60") W x 87.0 mm (3.43") H x 24.0 mm (0.94") D

Net Weight 80 grams (2.8 oz) (without batteries)


PLUG-ON TRANSMITTER SPECIFICATIONS

RF Power Output High: 30 mW; Low: 10 mW, nominal, Spurious Emissions Under federal regulations, Input Connector 3-pin locking XLRF-type, Batteries Two 1.5V AA alkaline (not included), Current Consumption High: 180 mA; Low: 160 mA, typical, Battery Life Approximately 6 hours (High); 8 hours (Low), depending on battery type and use pattern

Dimensions 40.0 mm (1.57") x 111.0 mm (4.37") x 40.0 mm (1.57")

Net Weight 199 grams (7.0 oz) (without batteries)

--------------------------------------------------------------------------------
Microphone Power (ATW-T1802 Plug-on Transmitter): Provides power to condenser microphones rated to
operate on 12V phantom power or less.

**Note: The 1800 Series offers UHF wireless operating frequencies in 25 kHz steps, while the 3000 Series offers UHF wireless operating frequencies in 125 kHz steps. This means that not every frequency selectable on 1800 Series components will be selectable on the 3000 Series components. Be certain to set each Transmitter-Receiver pair to identical frequencies

.--------------------------------------------------------------------------------